Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Blog Article
We've noticed the article relating to How to Install a Bathtub Yourself down the page on the net and figured it made good sense to relate it with you on my blog.
Mounting a tub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably challenging project. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and also place the new bath tub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will certainly need an assistant to leave the old tub and embeded in the brand-new one. Ensure you have actually qualified on your own for the work and also fit attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to think about using one before you start. Possibilities are you might need a professional plumber to make tube connections.
This article will certainly help you mount a new bath tub in your shower room if you have actually already acquired a new bathtub as well as do not need to change the plan of your previous water pipes.
Your devices and product checklist must comprise the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited access that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Using the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub until the level reads degree.
To set up faucets, fit the bottom of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water system and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait till the bathtub has actually been made use of a minimum of when as this will settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former kind needs to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the activity experienced when the tub remains in use. The sealant can crack fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is recommended to fit the tiles using water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our piece about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking time to browse our blog. Appreciated our posting? Please share it. Help somebody else discover it. I praise you for your time. Kindly pay a visit to our website back soon.
Book Maintenance
Report this page